Steps to move a upright piano

Pianos routinely make movers annual list of items that are most often damaged. Grand pianos are especially problematic. Practicing the following treatments for dismantling, cushioning and loading grand pianos will avoid damage, lower claims expenditure, and enhance consumer satisfaction.

1) A minimum of three people are required to handle a baby grand piano. If the child grand piano requires to go up or down stairs or if a complete or show grand piano needs to be carried, a minimum of 4 people are required.

2) Always finish a extensive and precise inventory. It might be required or more effective to utilize a visual inventory to effectively describe and show pre-existing damage.

3) As various parts are taken apart, please location all hardware in an appropriately labeled parts bag and then put the parts bag in a "Components Box".

4) Eliminate the music rack (lyre) from its track by pulling it toward the keyboard. Wrap it in a tidy furniture pad.

5) Disconnect the lid by getting rid of the hinge pins. Have a single person wiggle the lid, holding it opposite the hinge, while a 2nd individual works the pin loose. Please be careful not to damage the wood with the pliers or with the pin itself. If needed, cover the jaws of the pliers with a little fabric to help prevent damage to the wood. Wrap the lid in a clean furniture pad.

6) Eliminate the prop that holds the lid open and wrap it in a clean furniture pad. The prop has a hinge pin and is in two pieces.

7) Eliminate the pedal assembly and cover it in a clean furniture pad. The braces at the back of the assembly rest in slots at each end. When getting rid of the screws, please be careful not to drop the braces. In addition, please be specifically mindful with the push-rods so that they will not get bent. As you face the piano, number the push-rods from left to right as "1", "2", and "3", by placing a piece of masking tape with the appropriate number on each rod. Keep in mind: If masking tape is not available, please usage properly identified parts bags for this function. When reassembling at destination, please be sure to put the rods in the correct order so that the pedals will work effectively.

8) Pad the piano by putting a clean rolled furnishings pad (stretch-wrap the pad to prevent it from unrolling) on the cover of the keyboard to avoid it from flopping open while you manage the piano. Cover the top of the piano with 2 clean furnishings pads, neatly folded around the keyboard. Usage rubber bands to protect the pads. Keep in mind: Please guarantee that the surface area of the piano is dust-free before padding it. Padding an extremely polished surface that is dirty might this contact form cause great scratches, especially on a black lacquer finish.

9) Position a piano board and connect the straps so that it is ready to receive the piano. The raised brace on the piano board need to be at the keyboard end of the piano.

10) Get rid of the left front leg by placing one person underneath the piano at the left end of the keyboard. Be sure to have two people raising the corner of the piano while the third person gets rid of the leg. Keep in mind: Please be sure to keep in mind which legs were eliminated from which positions because some pianos have legs navigate to this website that are not interchangeable.

11) Place the piano on the piano board by decreasing the "leg-less" end onto the board. Please make sure to lift the whole piano slightly while finishing this maneuver to prevent excessive pressure on the remaining, connected legs as the piano ideas. Raise the piano to an upright position on the board. Note: Please guarantee that the soundboard is protected prior to lifting. Make sure that the piano is centered snugly versus the brace at the end of the piano board. Note: Never leave the piano ignored. Constantly have at least one person holding the piano constant at all times.

12) Eliminate the 2 staying legs and cover them in tidy furniture pads. These legs are held in place by a "key and slot" arrangement. To eliminate the leg, slide it inward towards the center of the piano till it comes out of the slot.

13) Protect the piano to the piano board by bringing completions of the straps together and attaching them. Location folded burlap pads over the furnishings pads however under the straps to supply extra defense to the edges of the piano. To avoid the strap near the narrow end of the piano from slipping off, connect the loose ends of the two straps together.

14) To move the piano over a flat, level surface area, tilt the piano and piano board and location a navigate here four-wheel dolly under the center of the piano board.

15) To move the piano up or down stairs, utilize the piano board as a skid. After adequately padding the stairs for security against residence damage, place the keyboard end of the piano towards the bottom of the stairs. Connect a hump strap to the leading end of the piano board to avoid the piano from slipping.

16) To pack the piano, leave it on the piano board and place it in a tier as the first base product with the keyboard facing the wall of the preceding tier. The best location to pack the padded cover is in between the piano and the preceding tier or between the wall and the piano.

Grand pianos represent a significant challenge, they can be moved without damage by utilizing common sense and practicing the treatments listed above.

Leave a Reply

Your email address will not be published. Required fields are marked *